LED Floodlight Housing — 50–400 W Outdoor
Outdoor floodlight enclosure for 50–400 W LED modules, with a cast or formed body, hinged glass bezel and a separate driver chamber that keeps heat away from the electronics. Bracket-mounted with a ±90° aiming range for facade, area and sports lighting. Made by WERIX Metal from AL ADC12 die-cast + AL5052 2.0mm to a tolerance of ±0.1mm, finished with outdoor powder coat IP65. Typical order volume is from 100 to 20000+. Free DFM quote within 24 hours.
Engineering drawing available on request
Send your target specifications — we reply with a drawing and a DFM quote within 24 hours.
LED Floodlight Housing — 50–400 W Outdoor
Outdoor floodlight enclosure for 50–400 W LED modules, with a cast or formed body, hinged glass bezel and a separate driver chamber that keeps heat away from the electronics. Bracket-mounted with a ±90° aiming range for facade, area and sports lighting.
| Part number | P-074 |
|---|---|
| Product type | Floodlight Housing |
| Industry | LED Lighting |
| Material | AL ADC12 die-cast + AL5052 2.0mm |
| Tolerance | ±0.1mm |
| Surface Finish | outdoor powder coat IP65 |
| Manufacturing processes | die casting · CNC machining |
| MOQ / Volume | from 100 to 20000+ |
LED Floodlight Housing — 50–400 W Outdoor: manufacturing notes
This part — led floodlight housing — 50–400 w outdoor — is manufactured in our Dongguan plant. The notes below explain the manufacturing decisions behind the specification: why this material, why this forming sequence, and what the tolerance actually requires in production.
Why this part is made in aluminium
LED Floodlight Housing — 50–400 W Outdoor is specified in AL ADC12 die-cast + AL5052 2.0mm. Aluminium buys weight reduction and thermal conductivity, at the cost of stiffness: a section that is stiff enough in 1.5 mm steel needs either a thicker gauge or formed stiffeners in aluminium. It anodises rather than paints when a hard, non-flaking surface is wanted, and it needs dedicated tooling and fixturing because the soft surface marks easily during handling.
How the part is formed
The production route for this part is die casting, CNC machining. Stamping moves the cost from the labour line to a hardened die, which pays off from a few thousand pieces upward: cycle time stops being a labour cost and becomes machine time, and every subsequent part inherits the die’s tolerances instead of the operator’s. Below that volume the same geometry is normally lasered and formed.
What ±0.1mm actually requires on the shop floor
The drawing calls for ±0.1mm. On a part like this that is a process decision, not an inspection decision: it fixes which machine holds the critical features, how the part is fixtured for each operation, and whether a formed feature can be checked after coating or has to be measured before it. We confirm the first article against the drawing and record the values, so the tolerance is demonstrated rather than assumed. If a dimension in your drawing is tighter than this part needs, it is usually worth relaxing it — over-toleranced features are one of the quietest cost drivers in a sheet metal quote.
Finishing: powder coating
outdoor powder coat IP65. Powder coating builds a film of roughly 60–120 µm per face and cures at 180–200 °C. Two consequences get designed for: the film adds to every mating dimension, and the cure temperature is high enough to move an unsupported panel, so stiffening or return flanges go in before the part reaches the oven. Colour is matched to the RAL range given on the drawing.
Frequently asked questions
- What is the minimum order quantity for led floodlight housing — 50–400 w outdoor?
- The order range for this part is from 100 to 20000+. Below the low end of that range the tooling and setup are spread over too few pieces to be economic, so if you are prototyping we would normally build the first units from the same process route and quote the production quantity separately.
- Can the material be changed to reduce cost or weight?
- Yes, and it is worth asking before the design is frozen. The current specification for this part is AL ADC12 die-cast + AL5052 2.0mm; depending on the service environment, a different grade or a lighter gauge with formed stiffening can meet the same requirement. What we would not do is change the material without re-checking the bend radii, the welding process and the coating system, because all three move with the substrate.
- What finishing options are available for this part?
- The current finish specification is outdoor powder coat IP65. Powder coating, anodising, zinc or nickel plating, brushing and blasting are all available in-house, so the finish can be changed without changing supplier — and where the part will be seen, we match colour to the RAL or Pantone reference on your drawing.
- How long does production take, and what do you need from us to quote?
- Prototypes are typically 3–7 business days and production runs 7–15 days once the drawing is released and the finish is confirmed. To quote we need the drawing or CAD file (STEP, DXF, DWG, IGES or PDF), the material and finish, the quantity and the destination — and any tolerance or inspection requirement that is not already on the drawing. You get a DFM review with the quotation, not after it.
Sheet metal engineering guides
Zinc Plating vs Nickel PlatingZinc protects steel even when scratched, for cents. Nickel is harder and brighter but 3-5x the cost. The finish decision, in one table.Read More
Powder Coating vs Anodizing: How to ChoosePowder wins on colour and substrate range; anodizing wins on wear and thinness. Five rules that decide it, with the cost drivers behind each.Read More