Smart Home Hub/Device Housing
Sheet metal enclosures for smart speakers, hubs, routers, and home controllers. Features a refined sandblasted anodized finish that complements modern smart home aesthetics while providing excellent durability. Made by WERIX Metal from AL5052-H32 1.0mm to a tolerance of ±0.1mm, finished with anodizing Type II + sandblasting. Typical order volume is from 100 to 20000+. Free DFM quote within 24 hours.
Engineering drawing available on request
Send your target specifications — we reply with a drawing and a DFM quote within 24 hours.
Smart Home Hub/Device Housing
Sheet metal enclosures for smart speakers, hubs, routers, and home controllers. Features a refined sandblasted anodized finish that complements modern smart home aesthetics while providing excellent durability.
| Part number | P-063 |
|---|---|
| Product type | Smart Home Housing |
| Industry | Consumer Electronics |
| Material | AL5052-H32 1.0mm |
| Tolerance | ±0.1mm |
| Surface Finish | anodizing Type II + sandblasting |
| Manufacturing processes | precision laser · CNC bending · anodizing |
| MOQ / Volume | from 100 to 20000+ |
Smart Home Hub/Device Housing: manufacturing notes
Smart Home Hub/Device Housing has to survive its application, not just its inspection report. This page sets out how the part is actually made — the material decision, the forming sequence and the tolerance strategy — so a buyer or engineer can judge whether the specification matches the application before a drawing is even sent.
Why this part is made in aluminium
Smart Home Hub/Device Housing is specified in AL5052-H32 1.0mm. Aluminium buys weight reduction and thermal conductivity, at the cost of stiffness: a section that is stiff enough in 1.5 mm steel needs either a thicker gauge or formed stiffeners in aluminium. It anodises rather than paints when a hard, non-flaking surface is wanted, and it needs dedicated tooling and fixturing because the soft surface marks easily during handling.
How the part is formed
The production route for this part is precision laser, CNC bending, anodizing. Bending is where most tolerance stack enters a sheet metal part. We set the bend allowance from the part’s own material and radius using the K-factor the press is running, then verify the first article on the machine rather than from the drawing, because springback moves with material batch and grain direction.
What ±0.1mm actually requires on the shop floor
The drawing calls for ±0.1mm. On a part like this that is a process decision, not an inspection decision: it fixes which machine holds the critical features, how the part is fixtured for each operation, and whether a formed feature can be checked after coating or has to be measured before it. We confirm the first article against the drawing and record the values, so the tolerance is demonstrated rather than assumed. If a dimension in your drawing is tighter than this part needs, it is usually worth relaxing it — over-toleranced features are one of the quietest cost drivers in a sheet metal quote.
Finishing: anodising
anodizing Type II + sandblasting. Anodising converts the aluminium surface into a hard oxide layer instead of adding a film, so it does not chip and flake the way a coating can. It is the reason aluminium parts often ship anodised rather than painted, and the layer thickness is chosen for the service — decorative, wear-resistant or hard-anodised for moving surfaces.
Frequently asked questions
- What is the minimum order quantity for smart home hub/device housing?
- The order range for this part is from 100 to 20000+. Below the low end of that range the tooling and setup are spread over too few pieces to be economic, so if you are prototyping we would normally build the first units from the same process route and quote the production quantity separately.
- Can the material be changed to reduce cost or weight?
- Yes, and it is worth asking before the design is frozen. The current specification for this part is AL5052-H32 1.0mm; depending on the service environment, a different grade or a lighter gauge with formed stiffening can meet the same requirement. What we would not do is change the material without re-checking the bend radii, the welding process and the coating system, because all three move with the substrate.
- What finishing options are available for this part?
- The current finish specification is anodizing Type II + sandblasting. Powder coating, anodising, zinc or nickel plating, brushing and blasting are all available in-house, so the finish can be changed without changing supplier — and where the part will be seen, we match colour to the RAL or Pantone reference on your drawing.
- How long does production take, and what do you need from us to quote?
- Prototypes are typically 3–7 business days and production runs 7–15 days once the drawing is released and the finish is confirmed. To quote we need the drawing or CAD file (STEP, DXF, DWG, IGES or PDF), the material and finish, the quantity and the destination — and any tolerance or inspection requirement that is not already on the drawing. You get a DFM review with the quotation, not after it.
Sheet metal engineering guides
Powder Coating vs Anodizing: How to ChoosePowder wins on colour and substrate range; anodizing wins on wear and thinness. Five rules that decide it, with the cost drivers behind each.Read More
8 Proven Ways to Cut Sheet Metal Costs Without Sacrificing QualityFrom bend radius optimization to material nesting — eight actionable design and sourcing strategies that reduce cost while maintaining part performance.Read More