Dishwasher Inner Drum & Tank Panel
Dishwasher inner tank panels and drum sections in 304 stainless: laser-welded seams ground smooth, drain and filter apertures formed without burrs, and passivation after welding so detergent and hot water do not attack the weld zone first. Made by WERIX Metal from SUS304 0.5mm to a tolerance of ±0.1mm, finished with brushed stainless interior. Typical order volume is from 1000 to 100000+. Free DFM quote within 24 hours.
Engineering drawing available on request
Send your target specifications — we reply with a drawing and a DFM quote within 24 hours.
Dishwasher Inner Drum & Tank Panel
Dishwasher inner tank panels and drum sections in 304 stainless: laser-welded seams ground smooth, drain and filter apertures formed without burrs, and passivation after welding so detergent and hot water do not attack the weld zone first.
| Part number | P-111 |
|---|---|
| Product type | Dishwasher Drum |
| Industry | Home Appliances |
| Material | SUS304 0.5mm |
| Tolerance | ±0.1mm |
| Surface Finish | brushed stainless interior |
| Manufacturing processes | deep drawing · stamping · TIG welding |
| MOQ / Volume | from 1000 to 100000+ |
Dishwasher Inner Drum & Tank Panel: manufacturing notes
Dishwasher Inner Drum & Tank Panel has to survive its application, not just its inspection report. This page sets out how the part is actually made — the material decision, the forming sequence and the tolerance strategy — so a buyer or engineer can judge whether the specification matches the application before a drawing is even sent.
Why this part is made in stainless steel
Dishwasher Inner Drum & Tank Panel is specified in SUS304 0.5mm. Stainless is specified for corrosion resistance and for appearance in one move: the surface is the corrosion protection, so a scratch is a maintenance question rather than a rust path. It work-hardens as it is formed, which raises the bend force and pushes springback up, so bend radii on stainless are kept larger than on mild steel and the tooling is set for the higher force.
How the part is formed
The production route for this part is deep drawing, stamping, TIG welding. Deep drawing forms a part from a single blank, so there is no seam to seal or finish. The material is stretched rather than folded, which means the draw ratio and the blank-holder force are the design constraints, and the finish has to be applied after forming because the surface is displaced. Stamping moves the cost from the labour line to a hardened die, which pays off from a few thousand pieces upward: cycle time stops being a labour cost and becomes machine time, and every subsequent part inherits the die’s tolerances instead of the operator’s. Below that volume the same geometry is normally lasered and formed.
What ±0.1mm actually requires on the shop floor
The drawing calls for ±0.1mm. On a part like this that is a process decision, not an inspection decision: it fixes which machine holds the critical features, how the part is fixtured for each operation, and whether a formed feature can be checked after coating or has to be measured before it. We confirm the first article against the drawing and record the values, so the tolerance is demonstrated rather than assumed. If a dimension in your drawing is tighter than this part needs, it is usually worth relaxing it — over-toleranced features are one of the quietest cost drivers in a sheet metal quote.
Finishing: brushed finish
brushed stainless interior. Brushing lays a directional grain into the surface, which hides handling marks on stainless and aluminium and reads as a deliberate industrial finish. The grain direction is specified on the drawing because it changes how the part looks under different lighting, especially across a bend.
Frequently asked questions
- What is the minimum order quantity for dishwasher inner drum & tank panel?
- The order range for this part is from 1000 to 100000+. Below the low end of that range the tooling and setup are spread over too few pieces to be economic, so if you are prototyping we would normally build the first units from the same process route and quote the production quantity separately.
- Can the material be changed to reduce cost or weight?
- Yes, and it is worth asking before the design is frozen. The current specification for this part is SUS304 0.5mm; depending on the service environment, a different grade or a lighter gauge with formed stiffening can meet the same requirement. What we would not do is change the material without re-checking the bend radii, the welding process and the coating system, because all three move with the substrate.
- What finishing options are available for this part?
- The current finish specification is brushed stainless interior. Powder coating, anodising, zinc or nickel plating, brushing and blasting are all available in-house, so the finish can be changed without changing supplier — and where the part will be seen, we match colour to the RAL or Pantone reference on your drawing.
- How long does production take, and what do you need from us to quote?
- Prototypes are typically 3–7 business days and production runs 7–15 days once the drawing is released and the finish is confirmed. To quote we need the drawing or CAD file (STEP, DXF, DWG, IGES or PDF), the material and finish, the quantity and the destination — and any tolerance or inspection requirement that is not already on the drawing. You get a DFM review with the quotation, not after it.
Sheet metal engineering guides
Powder Coating vs Anodizing: How to ChoosePowder wins on colour and substrate range; anodizing wins on wear and thinness. Five rules that decide it, with the cost drivers behind each.Read More
8 Proven Ways to Cut Sheet Metal Costs Without Sacrificing QualityFrom bend radius optimization to material nesting — eight actionable design and sourcing strategies that reduce cost while maintaining part performance.Read More