Solar Mounting Bracket/Rail
Aluminum structural mounting systems for rooftop and ground-mount solar panel arrays, including C-channels, Z-purlins, mid clamps, end clamps, and L-foot brackets. Designed for rapid installation with pre-punched bolt holes and universal panel compatibility from 60-cell to 72-cell modules. Made by WERIX Metal from AL6063-T5 aluminum extrusion to a tolerance of ± 0.1 mm, finished with Anodizing Type II, 15µm. Typical order volume is From 100 sets to 50,000+ volume. Free DFM quote within 24 hours.
Engineering drawing available on request
Send your target specifications — we reply with a drawing and a DFM quote within 24 hours.
Solar Mounting Bracket/Rail
Aluminum structural mounting systems for rooftop and ground-mount solar panel arrays, including C-channels, Z-purlins, mid clamps, end clamps, and L-foot brackets. Designed for rapid installation with pre-punched bolt holes and universal panel compatibility from 60-cell to 72-cell modules.
| Part number | P-022 |
|---|---|
| Product type | bracket |
| Industry | New Energy |
| Material | AL6063-T5 aluminum extrusion |
| Tolerance | ± 0.1 mm |
| Surface Finish | Anodizing Type II, 15µm |
| Manufacturing processes | Extrusion Profiling · CNC Machining · Cutting |
| MOQ / Volume | From 100 sets to 50,000+ volume |
Solar Mounting Bracket/Rail: manufacturing notes
Every part we ship has to perform in service, not just pass inspection. Below is how this solar mounting bracket/rail is specified and manufactured at WERIX, and which details in the drawing drive cost, lead time and yield.
Why this part is made in aluminium
Solar Mounting Bracket/Rail is specified in AL6063-T5 aluminum extrusion. Aluminium buys weight reduction and thermal conductivity, at the cost of stiffness: a section that is stiff enough in 1.5 mm steel needs either a thicker gauge or formed stiffeners in aluminium. It anodises rather than paints when a hard, non-flaking surface is wanted, and it needs dedicated tooling and fixturing because the soft surface marks easily during handling.
What ± 0.1 mm actually requires on the shop floor
The drawing calls for ± 0.1 mm. On a part like this that is a process decision, not an inspection decision: it fixes which machine holds the critical features, how the part is fixtured for each operation, and whether a formed feature can be checked after coating or has to be measured before it. We confirm the first article against the drawing and record the values, so the tolerance is demonstrated rather than assumed. If a dimension in your drawing is tighter than this part needs, it is usually worth relaxing it — over-toleranced features are one of the quietest cost drivers in a sheet metal quote.
Finishing: anodising
Anodizing Type II, 15µm. Anodising converts the aluminium surface into a hard oxide layer instead of adding a film, so it does not chip and flake the way a coating can. It is the reason aluminium parts often ship anodised rather than painted, and the layer thickness is chosen for the service — decorative, wear-resistant or hard-anodised for moving surfaces.
Frequently asked questions
- What is the minimum order quantity for solar mounting bracket/rail?
- The order range for this part is From 100 sets to 50,000+ volume. Below the low end of that range the tooling and setup are spread over too few pieces to be economic, so if you are prototyping we would normally build the first units from the same process route and quote the production quantity separately.
- Can the material be changed to reduce cost or weight?
- Yes, and it is worth asking before the design is frozen. The current specification for this part is AL6063-T5 aluminum extrusion; depending on the service environment, a different grade or a lighter gauge with formed stiffening can meet the same requirement. What we would not do is change the material without re-checking the bend radii, the welding process and the coating system, because all three move with the substrate.
- What finishing options are available for this part?
- The current finish specification is Anodizing Type II, 15µm. Powder coating, anodising, zinc or nickel plating, brushing and blasting are all available in-house, so the finish can be changed without changing supplier — and where the part will be seen, we match colour to the RAL or Pantone reference on your drawing.
- How long does production take, and what do you need from us to quote?
- Prototypes are typically 3–7 business days and production runs 7–15 days once the drawing is released and the finish is confirmed. To quote we need the drawing or CAD file (STEP, DXF, DWG, IGES or PDF), the material and finish, the quantity and the destination — and any tolerance or inspection requirement that is not already on the drawing. You get a DFM review with the quotation, not after it.
Sheet metal engineering guides
Powder Coating vs Anodizing: How to ChoosePowder wins on colour and substrate range; anodizing wins on wear and thinness. Five rules that decide it, with the cost drivers behind each.Read More
DFM for Sheet Metal: Essential Design Rules That Save Cost and Prevent Production FailuresDesign-for-manufacturing rules for sheet metal — minimum hole sizes, bend radii, edge distances, tab-and-slot design, and common mistakes that cause scrap.Read More